Phanxuan Phuc

fakerphan

I’m a AI Engineer in Vin Bigdata. And I summarize research papers in these topics:

5 mins read

Published by: University of Edinburgh

Back-translation

Back-translation is a semi-supervised mechanism proposed in this paper: “Improving Neural Machine Translation Models with Monolingual Data” by the Rico Sennrich and the University of Edinburgh in 2015 that uses a reverse translation system make the best use out of target-side monolingual data.

Back-translation operates in a semi-supervised setup where both bilingual and monolingual data in the target language are available. Using “English-French” data as a use-case where the source is English and the target is French, the back-translation process can be summarized into the following steps:

  • We have “en-fr” parallel corpus that can be used to train NMT model, let’s call it “Forward NMT en→fr”.

  • We can reverse this data to get “fr-en” parallel corpus which can be used to train NMT model, let’s call it “Backward NMT en→fr”.

  • We have a corpus of just “French” data.

  • We will use the “Backward NMT en→fr” to translate this French data to English which will get us a “synthetic en-fr parallel corpus”. To be able to get the best synthetic data possible, the paper uses beam search.

  • Then, we are going to mix the original “en-fr” data with the synthetic one to further train the “forward NMT en→fr” model.

You could either leave it at that (hopefully better than just the original model), or you can extend it to dual learning where you have to find some monolingual source language data and translate it with the forward model to further train the backward model (back-translation for the backward model). With this strengthened backwards model, you can probably generate better back-translations for the forward model, and train that one further and so on.

Notes:

  • You can iteratively train both models forever, but that only makes sense if you have monolingual source data as well, and it usually stops improving after a two rounds or so.

  • In the paper, they were using the encoder-decoder architecture. However, this technique can be used with any other NMT architecture.

  • As discussed in the paper, back-translation delays overfitting in NMT models especially for small datasets.

  • Usually, back-translation outperforms deep fusion.

In the paper, they tried another method to use monolingual target data hoping it will be better than the previous one. They treated the monolingual target data as parallel examples with empty source side. Which means that the decoder has to depend only on the previously generated word when generating the translation. Also, they froze the layers of the encoder.

The following are the different results obtained by each method on English -> German parallel corpus where:

  • parallel: means using just the NMT model

  • monolingual: means using the NMT model with monolingual data where the source source sentence is empty.

  • synthetic: means using the NMT model with monolingual data where the source sentence is translated using a backward NMT model.

Noised BT

Back-translation typically uses beam search to generate synthetic source sentences. However, beam search can lead to less rich translations since it focuses on the head of the model distribution which results in very regular synthetic source sentences that do not properly cover the true data distribution. In this paper: “Understanding Back-Translation at Scale”, published by Facebook AI and Google Brain in 2018, they advised that adding noise to the beam search actually improves the generated synthetic data which improves the translation model’s performance.

In particular, we transform source sentences with three types of noise:

  • Deleting words with probability 0.1.

  • Replacing words by a filler token with probability 0.1.

  • Uniformly swapping words no further than three positions apart.

And this simple change outperforms all other sampling techniques such as greedy search, beam search (beam size = 5), top-k sampling (k = 10), and randomly sampling. The following table contains the BLEU score of the same back-translation NMT model with different synthetic data generation methods:

And the following table shows the perplexity of the generated synthetic data. They analyzed the richness of generated synthetic outputs and train a language model on real human text and score synthetic source sentences generated by the different methods mentioned above:

The results show that beam+noise method receives the highest perplexity which indicates that beam search outputs are not as rich as sampling outputs or beam+noise. This lack of variability probably explains in part why back-translations from pure beam search provide a weaker training signal than alternatives.

Low vs High Resource

The experiments so far are based on a setup with a high-resource bilingual corpus. In this part, we are going to discuss the effect of back-translation on low-resource setup. To simulate such setups, they cut off the training data to either 80K sentence-pairs or 640K sentence-pairs and then used back-translation and compared this setup to the original setup.

The following figure shows that the accuracy of the German-English back-translation systems steadily increases with more training data: On newstest2012, the BLEU score is $13.5$ for 80K bitext, $24.3$ for 640K and $28.3$ BLEU for 5M:

The figure also shows that sampling is more effective than beam for larger setups (640K and 5.2M bi-texts) while the opposite is true for resource poor settings (80K bitext). This is likely because the back-translations in the 80K setup are of very poor quality and the noise of sampling and beam+noise is too much for this brittle low-resource setting.

Real Vs Synthetic Data

How does real human bitext compare to synthetic data in terms of final model accuracy? To answer this question, they sub-sampled 640k sentence-pairs of the bitext for training. And added either one of the following three alternatives:

  • bitext: The remaining of bitext data (real human).

  • BT-bitext: The back-translation of the remaining bitext data (synthetic).

  • BT-news: The back-translation the news data (synthetic, different domain).

The back-translated data is generated via sampling. This setup allows us to compare synthetic data to genuine data since BT-bitext and bitext share the same target side. It also allows us to estimate the value of BT data for domain adaptation since the newscrawl corpus (BT-news) is pure news whereas the WMT is a mixture of europarl and commoncrawl.

The following figure shows the results on both validation sets. Most strikingly, BT-news performs almost as well as bitext on newstest2012. This shows that synthetic data can be nearly as effective as real human translated data when the domains match:

On the other hand, when the domain changes, the back-translation performance gets hurt. The following figure shows the performance of the previous three models on a mixture set between WMT training data & news crawl. They named this set “valid-mixed”. The following figure shows the accuracy is not as good as before since the domain of the BT data and the test set do not match: